home-Air conditioning equipment-Ionizer-How to install a water and air ionizer

How to install a water and air ionizer

Air ionizer can be found in any home. It prevents the proliferation of viruses, prevents the spread of bad odors, improves microcirculation of air, moderately moisturizes it, and strengthens the immune system. Negatively charged electrons exiting the apparatus destroy pathogens at the molecular level.

People suffering from hypertension, diseases of the lungs and bronchi, need to breathe clean forest mountain air. But since many do not have such an opportunity, it is enough to put a bipolar ionizer in the apartment. Due to the proper operation of the device will serve efficiently and for a long time.

The story of the appearance of ionizers begins with Russia, the first chandelier for air purification was invented by the scientist Chizhevsky.

Vitek ionizer simultaneously purifies and moisturizes the air

Installation of a water ionizer in an apartment

Consider the example of an AQUASPECTR device. The procedure is as follows:

  1. The device has features - plugs that must be removed so that no debris gets inside the case. Otherwise, the device will not be able to function normally. The plugs are located at the bottom of the ionizer: at the inlet and outlet. Some ionizers are located in the upper part.
  2. The plugs are removed with a flat screwdriver so as not to damage the mechanism. Unnecessary parts must not be thrown away; they should be carefully laid and stored in cellophane. Then you need to carry out installation at the place selected for the device.
  3. Fix the device on the wall, attach the tubes to the “input” and “output” zones. Install a filtration system. A three-stage or four-stage filter will perform the task of purifying water.
  4. When installing the purifier, workers must install an additional tap. Before installing the water ionizer, you must remove the tube of the additional tap.
  5. Insert the connection pipe into the tap so that there are no holes. This tube will go to the inlet input system. Exiting the ionizer system removes positively charged water into the antlet sewer.
  6. AQUASPECTR water works using the control panel. The green button is “on”, the red is “off”. Position AQUASPECTR 2 meters from the electric meter, fan.

The ionizer saturates water with negative electrons, making it healthy

Air cleaning ionizer

To install an Eco-Norm ionizer in an apartment, it is enough to fix it on the wall and press the corresponding button. Today in stores combined models are presented, including an ionizer and an ozonizer in one device. For people suffering from respiratory diseases, it is better to use a bipolar device, turn on for 10-15 minutes.

Eco norms designed for car and rooms

Car ionizer installation

Ionizer in the car, fix under the hood of the car

Consider the installation procedure using the HM069 as an example:

  1. Determine the location available for installation. Avoid hot and humid places. Wires can melt when exposed to high temperatures. High voltage appliance and water spray are not compatible.
  2. We remove the protective cover from the reactor, the unit itself can be attached to the battery. It is important that the high-voltage part is as far from the metal as possible (below is how to conduct it). The reactor itself under the hood should also be located farther from water and hot spots in the car.
  3. Connect the negative wire (blue) from the device (coming from the side of the power indicator) to the negative terminal of the battery.To fix not on weight, not on the case, but on the minus terminal, usually people forget about it.
  4. We fasten the reactor on a plinth to the selected place. The pipe line prepared with a mixture of nitrogen can be bought at technical stores. This is necessary in order to conduct the inlet of the duct, which leads to the filter. The length of the hose is about 1 meter.
  5. Connect the central part of the generator and the high-voltage cable with a white wire. We connect the mass of the reactor (black wire) with the blue wire (which extends from the side of the high-voltage part), make a terminal so that it can be connected to the body mass (car body, piece of metal).
  6. Install the positive terminal (yellow wire) on the fuel pump relay so that, together with turning the ignition key, the gas pump and ionizer are simultaneously turned on. Before installation, check how the device itself works, for this you need to install the yellow wire on the positive terminal of the battery. Turn on the device. Normally, the device should hiss, and the indicator light will light up. If the wires are very long, it is necessary to cut them to avoid adverse effects on the mechanisms of the car.

Installation of other ionizers:

  • AIR COMFORT GH-2151. It is installed in the passenger compartment. Connect the 12 V adapter to the cigarette lighter for 20-30 minutes. It can also be used in an apartment. Do not use more than 4 hours a day. Small dimensions allow you to use the device everywhere, easy to carry in any room.
  • JUM001215 is small in size. Screws into the cigarette lighter, eliminates unpleasant odors through the operation of an ultraviolet lamp. Do not use more than 5 hours a day. Glows with a pleasant violet light. Simple and easy to use. To avoid hit of water on the device case.

Ionizer in a car, size up to 20 cm

Recommendations

Unipolar ionizers, unlike bipolar ones, saturate the air with negative and positive particles. It is not recommended to turn on the device in dusty rooms, it may fail due to a large amount of dust. From you, the distance to the apparatus should be approximately at least 1 meter. If the house has a child under 1 year old, the purchase of a cleaning device is extremely dangerous.

If the power is not indicated in the documents of the device, it is not recommended to buy it. This model is not standardized and not tested for safety, it is possible that the amount of ozone exceeds the maximum permissible norm, which may entail the development of oncology and other dangerous diseases.

Homemade devices can also be a useful source of negatively charged particles. But you need to properly manufacture such a device and check for quality using an indicator and other home methods.

leave a comment